ABB · Power Supplies & UPS
ABB 2000 repair
Get the ABB 2000 repaired rather than replaced. It is matched to an engineer who works on ABB power supplys, and the cost is confirmed before work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The ABB 2000
- Manufacturer
- ABB
- Model / part number
- 2000
- Description
- Module, freelance link P 37151-4-0369642
- Category
- Power Supplies & UPS
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
ABB equipment in Indian plants ranges from ACS and DCS series drives and Unitrol excitation systems to AC500 PLCs, 800xA and older DCS hardware, protection relays and robot controllers.
Common faults
What usually fails on a unit like the 2000
Power supplies are the most common single cause of machine electronics failing. Switched-mode supplies wear out in predictable places, mainly capacitors, switching transistors and fans, and almost all of them can be repaired and load-tested.
No output
Failed fuse, switching transistor, controller IC or startup circuit, often triggered by a surge.
Low, noisy or drifting output
Dried-out electrolytic capacitors are the most common cause, and they cause resets and odd faults in the equipment downstream.
Shutdown under load
Overload protection tripping because of a weak supply, or a short in the load.
Overheating
Failed fans and dust build-up in fan-cooled supplies and UPS units.
UPS battery and charger faults
Ageing batteries and failed charger circuits reduce backup time or cause transfer failures.
Communication
Communication faults can be in the module, the cable or the network configuration. The module is tested on a live link after repair; the cabling and terminations at site are worth checking too.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Measure the output voltage with and without load.
- Disconnect the load to see whether the supply or the load is at fault.
- Check fans and ventilation.
Leave to a specialist
- Opening a supply: its capacitors hold a charge after switch-off.
- Component-level repair and load testing.
- Battery replacement in UPS units.
Getting it fixed
How to get the 2000 repaired
What to send with it
- The supply or UPS module.
- Its input and output ratings if the label is unreadable.
- What it feeds, and whether it failed suddenly or gradually.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
2000 repair questions
Is it worth repairing the ABB 2000 rather than buying a new one?+
For standard supplies it depends on availability and price; for machine-specific, discontinued or high-power supplies, repair is usually the practical route because an exact replacement may not exist.
Does the ABB 2000 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to ABB?+
No. ABB and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by ABB.
Same manufacturer
Other ABB Power Supplies & UPS
Other manufacturers
Power Supplies & UPS from other makers
ABB and 2000 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by ABB.
2000 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.