Atos · Hydraulic & Pneumatic Controls
Atos E-RI-TEB-N-NP-05H repair
Send the Atos E-RI-TEB-N-NP-05H for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original hydraulic control, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Atos E-RI-TEB-N-NP-05H
- Manufacturer
- Atos
- Model / part number
- E-RI-TEB-N-NP-05H
- Also searched as
- ERITEBNNP05H · E RI TEB N NP 05H
- Description
- Valve, directional control 11
- Category
- Hydraulic & Pneumatic Controls
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Atos equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the E-RI-TEB-N-NP-05H
Proportional and servo valves, their amplifier cards and actuator controls link electronics to hydraulics. Faults can sit in the valve's coil or electronics, the amplifier card or the hydraulics, and each is checked separately.
Amplifier card faults
Failed output stages or supplies on valve amplifier cards cause no movement or full-on valves.
On-board valve electronics
Integrated electronics fail through heat, vibration or supply surges.
Coil failures
Open or shorted solenoid coils.
Contamination
Dirty oil causes sticking spools and erratic control, which can look like an electronics fault.
Feedback sensor faults
Spool position and pressure feedback sensors giving wrong signals.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the command signal and supply to the valve or card.
- Check oil condition and filters.
- Note whether movement is absent, erratic or stuck at one end.
Leave to a specialist
- Valve electronics and amplifier repair.
- Setting gain, offset and ramps.
- Work on pressurised hydraulics.
Getting it fixed
How to get the E-RI-TEB-N-NP-05H repaired
What to send with it
- The amplifier card or valve electronics.
- The valve model it drives.
- The settings or potentiometer positions, photographed.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
E-RI-TEB-N-NP-05H repair questions
Does the valve need to be sent with the Atos E-RI-TEB-N-NP-05H?+
For an amplifier card, not necessarily; it can be tested on a load. Send the valve too if it has integrated electronics or the fault might be in its coil or feedback.
Does the Atos E-RI-TEB-N-NP-05H have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Atos?+
No. Atos and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Atos.
Same manufacturer
Other Atos Hydraulic & Pneumatic Controls
Other manufacturers
Hydraulic & Pneumatic Controls from other makers
Atos and E-RI-TEB-N-NP-05H are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Atos.
E-RI-TEB-N-NP-05H down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.