B&R · PLCs & I/O Modules
B&R X20CP0171 repair
Send the B&R X20CP0171 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original PLC module, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The B&R X20CP0171
- Manufacturer
- B&R
- Model / part number
- X20CP0171
- Category
- PLCs & I/O Modules
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
B&R (now part of ABB) makes machine automation hardware: X20 and older PLC systems, Power Panel and Automation PC operator units, and ACOPOS servo drives with matching motors. It is common on packaging, printing and plastics machinery.
Common faults
What usually fails on a unit like the X20CP0171
PLC hardware is reliable, so when a module fails there is usually a clear cause: power supply stress, a surge on field wiring, heat, or age. CPUs, I/O modules, communication cards and power supplies can be repaired and tested on a live rack.
Power supply module failure
The whole rack goes dark or resets. Ageing capacitors and supply surges are the usual causes.
I/O channel damage
Single dead inputs or outputs after a short or surge on field wiring. The module is repaired and every channel tested.
CPU faults and lost programs
A CPU stuck in stop or fault mode, or a lost program from a flat memory battery. Keep a current backup of the program.
Communication module faults
Loss of the network to drives, remote I/O or the SCADA system, with the CPU itself healthy.
Backplane and connector problems
Intermittent module faults caused by the rack, connectors or vibration rather than the module.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note the CPU and module LEDs and any diagnostic buffer messages.
- Check the supply voltage to the rack.
- Take a program backup while the CPU still runs.
- Check field wiring for shorts before fitting a replacement module.
Leave to a specialist
- Downloading or modifying the program.
- Working on live I/O wiring.
- Replacing CPU firmware or memory.
Getting it fixed
How to get the X20CP0171 repaired
What to send with it
- The failed module, labelled with its slot position.
- The LED states and any diagnostic message.
- A program backup if a CPU is being sent.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
X20CP0171 repair questions
Will the B&R X20CP0171 keep its program after repair?+
A repair doesn't normally touch the user program, but a CPU should always be sent with a current backup in case its memory has been affected by the fault.
Can obsolete PLC modules still be repaired?+
Yes. Discontinued modules are usually worth repairing, because replacements are scarce and changing platforms means rewriting the program.
Does the B&R X20CP0171 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to B&R?+
No. B&R and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by B&R.
Same manufacturer
Other B&R PLCs & I/O Modules
Other manufacturers
PLCs & I/O Modules from other makers
B&R and X20CP0171 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by B&R.
X20CP0171 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.