Berger Lahr · Control Boards & PCBs
Berger Lahr CANBUS B170 repair
Component-level repair for the Berger Lahr CANBUS B170 (input card blscan), onsite or sent in from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Berger Lahr CANBUS B170
- Manufacturer
- Berger Lahr
- Model / part number
- CANBUS B170
- Also searched as
- CANBUSB170
- Description
- Input card blscan
- Category
- Control Boards & PCBs
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Berger Lahr equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the CANBUS B170
Control, interface and processor boards inside printing presses, chillers, compressors and special-purpose machines are often unavailable or very expensive as spares. Board-level repair finds the failed components and returns the original board.
On-board power faults
Failed regulators, DC-DC converters and capacitors stop the board or cause random resets.
Damaged inputs and outputs
Driver transistors, opto-couplers and relays damaged by shorts or surges in machine wiring.
Processor and memory faults
Failed processors, memory or corrupted firmware stop the board working.
Connector and track damage
Corrosion, burnt tracks and cracked solder joints, often from heat, vibration or moisture.
Communication faults
Failed serial, CAN or network interfaces between boards.
Inputs and outputs
I/O damage usually comes from the field wiring. After the module is repaired, every channel is tested, and the wiring it connects to should be checked for the short or surge that caused the failure.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Photograph connectors, jumpers and switches before removing the board.
- Note error messages from the machine.
- Check the supply voltages reaching the board.
Leave to a specialist
- Component-level fault-finding and repair.
- Testing the board with its inputs and outputs simulated.
- Firmware and memory work.
Getting it fixed
How to get the CANBUS B170 repaired
What to send with it
- The board, packed against static.
- The machine make and model it comes from.
- The fault and any error message.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
CANBUS B170 repair questions
Can the Berger Lahr CANBUS B170 be repaired without a circuit diagram?+
Usually, yes. Boards are traced and tested at component level. A known-good board for comparison helps but is not required.
Does the Berger Lahr CANBUS B170 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Berger Lahr?+
No. Berger Lahr and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Berger Lahr.
Same manufacturer
Other Berger Lahr Control Boards & PCBs
Other manufacturers
Control Boards & PCBs from other makers
- Technotrans ARTNR-202100023C MAT.NR-591294017-TT
- MAN Roland Card, audio frequency generator
- Hypertherm Control card, LUM MCC four axis SER ISO REV D of CNC plasma cutting machine
- BHEL Display, RTU Sigma with key pad
- Atlas Copco Elektronikon II keypad
- Agilent G3450-31801
- Toshiba IK-CU51
- Landis & Gyr LFL1.335
Berger Lahr and CANBUS B170 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Berger Lahr.
CANBUS B170 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.