Bronkhorst · Hydraulic & Pneumatic Controls
Bronkhorst F-202AV-M10-AGD-00-A repair
Component-level repair for the Bronkhorst F-202AV-M10-AGD-00-A (el-flow mass flow meter-controller), onsite or sent in from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Bronkhorst F-202AV-M10-AGD-00-A
- Manufacturer
- Bronkhorst
- Model / part number
- F-202AV-M10-AGD-00-A
- Also searched as
- F202AVM10AGD00A · F 202AV M10 AGD 00 A
- Description
- El-flow MASS flow meter-controller
- Category
- Hydraulic & Pneumatic Controls
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Bronkhorst equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the F-202AV-M10-AGD-00-A
Proportional and servo valves, their amplifier cards and actuator controls link electronics to hydraulics. Faults can sit in the valve's coil or electronics, the amplifier card or the hydraulics, and each is checked separately.
Amplifier card faults
Failed output stages or supplies on valve amplifier cards cause no movement or full-on valves.
On-board valve electronics
Integrated electronics fail through heat, vibration or supply surges.
Coil failures
Open or shorted solenoid coils.
Contamination
Dirty oil causes sticking spools and erratic control, which can look like an electronics fault.
Feedback sensor faults
Spool position and pressure feedback sensors giving wrong signals.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the command signal and supply to the valve or card.
- Check oil condition and filters.
- Note whether movement is absent, erratic or stuck at one end.
Leave to a specialist
- Valve electronics and amplifier repair.
- Setting gain, offset and ramps.
- Work on pressurised hydraulics.
Getting it fixed
How to get the F-202AV-M10-AGD-00-A repaired
What to send with it
- The amplifier card or valve electronics.
- The valve model it drives.
- The settings or potentiometer positions, photographed.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
F-202AV-M10-AGD-00-A repair questions
Does the valve need to be sent with the Bronkhorst F-202AV-M10-AGD-00-A?+
For an amplifier card, not necessarily; it can be tested on a load. Send the valve too if it has integrated electronics or the fault might be in its coil or feedback.
Does the Bronkhorst F-202AV-M10-AGD-00-A have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Bronkhorst?+
No. Bronkhorst and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Bronkhorst.
Same manufacturer
Other Bronkhorst Hydraulic & Pneumatic Controls
Other manufacturers
Hydraulic & Pneumatic Controls from other makers
Bronkhorst and F-202AV-M10-AGD-00-A are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Bronkhorst.
F-202AV-M10-AGD-00-A down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.