FANUC · Motion & Speed Controllers
FANUC A06B-6400-H102 repair
Send the FANUC A06B-6400-H102 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original motion controller, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The FANUC A06B-6400-H102
- Manufacturer
- FANUC
- Model / part number
- A06B-6400-H102
- Also searched as
- A06B6400H102 · A06B 6400 H102
- Description
- Servo amplifier
- Category
- Motion & Speed Controllers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
FANUC equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the A06B-6400-H102
Motion controllers, regulators and machine-specific drive cards coordinate speed, position or current. Faults appear as wrong movement, trips or loss of control, and the card is usually repairable at component level.
Loss of control or wrong speed
Faults in feedback inputs, reference signals or the control loop on the card.
Card dead or resetting
On-board supply faults and failed processors or memory.
Communication faults
Lost connection with the PLC, drives or the operator panel.
Output stage faults
Failed drivers for valves, contactors or power stages.
Crane and hoist control faults
Radio remote, interlock and speed-control faults on cranes and hoists.
Amplifier
Amplifiers are tested on a load after repair, with the output checked across its range.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note LEDs, alarm codes and when the fault occurs.
- Check reference and feedback wiring.
- Check the card's supply voltage.
Leave to a specialist
- Component-level repair and testing.
- Setting and tuning control loops.
- Work on crane and hoist safety circuits.
Getting it fixed
How to get the A06B-6400-H102 repaired
What to send with it
- The card or controller, with any plug-in modules.
- The machine it comes from and the fault seen.
- Its settings or jumper positions, photographed before removal.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
A06B-6400-H102 repair questions
Can the FANUC A06B-6400-H102 be repaired without drawings?+
In most cases. Boards are traced and repaired at component level and tested with their inputs and outputs simulated.
Does the FANUC A06B-6400-H102 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to FANUC?+
No. FANUC and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by FANUC.
Same manufacturer
Other FANUC Motion & Speed Controllers
Other manufacturers
Motion & Speed Controllers from other makers
FANUC and A06B-6400-H102 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by FANUC.
A06B-6400-H102 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.