Fluke · Power Supplies & UPS
Fluke 937404 repair
Send the Fluke 937404 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original power supply, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Fluke 937404
- Manufacturer
- Fluke
- Model / part number
- 937404
- Description
- Card, voltage A8 P/N
- Category
- Power Supplies & UPS
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Fluke makes handheld test and measurement instruments: multimeters, clamp meters, process calibrators, insulation testers, power quality analysers and thermal imagers used by maintenance teams.
Common faults
What usually fails on a unit like the 937404
Power supplies are the most common single cause of machine electronics failing. Switched-mode supplies wear out in predictable places, mainly capacitors, switching transistors and fans, and almost all of them can be repaired and load-tested.
No output
Failed fuse, switching transistor, controller IC or startup circuit, often triggered by a surge.
Low, noisy or drifting output
Dried-out electrolytic capacitors are the most common cause, and they cause resets and odd faults in the equipment downstream.
Shutdown under load
Overload protection tripping because of a weak supply, or a short in the load.
Overheating
Failed fans and dust build-up in fan-cooled supplies and UPS units.
UPS battery and charger faults
Ageing batteries and failed charger circuits reduce backup time or cause transfer failures.
Board-level repair
This is repaired at component level: the board is traced, the failed parts are replaced, and the board is tested with its inputs and outputs before it is returned.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Measure the output voltage with and without load.
- Disconnect the load to see whether the supply or the load is at fault.
- Check fans and ventilation.
Leave to a specialist
- Opening a supply: its capacitors hold a charge after switch-off.
- Component-level repair and load testing.
- Battery replacement in UPS units.
Getting it fixed
How to get the 937404 repaired
What to send with it
- The supply or UPS module.
- Its input and output ratings if the label is unreadable.
- What it feeds, and whether it failed suddenly or gradually.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
937404 repair questions
Is it worth repairing the Fluke 937404 rather than buying a new one?+
For standard supplies it depends on availability and price; for machine-specific, discontinued or high-power supplies, repair is usually the practical route because an exact replacement may not exist.
Does the Fluke 937404 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Fluke?+
No. Fluke and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Fluke.
Other manufacturers
Power Supplies & UPS from other makers
Fluke and 937404 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Fluke.
937404 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.