GE Fanuc · PLCs & I/O Modules
GE Fanuc PLC IC695ETM001-EJ RX3i repair
Get the GE Fanuc PLC IC695ETM001-EJ RX3i repaired rather than replaced. It is matched to an engineer who works on GE Fanuc PLC modules, and the cost is confirmed before work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The GE Fanuc PLC IC695ETM001-EJ RX3i
- Manufacturer
- GE Fanuc
- Model / part number
- PLC IC695ETM001-EJ RX3i
- Also searched as
- PLCIC695ETM001EJRX3i · PLC IC695ETM001 EJ RX3i
- Description
- ETHERNET module
- Category
- PLCs & I/O Modules
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
GE Fanuc PLCs and I/O, including the Series 90-30, 90-70, VersaMax and PACSystems families, are still common in plants, often long after their sale ended.
Common faults
What usually fails on a unit like the PLC IC695ETM001-EJ RX3i
PLC hardware is reliable, so when a module fails there is usually a clear cause: power supply stress, a surge on field wiring, heat, or age. CPUs, I/O modules, communication cards and power supplies can be repaired and tested on a live rack.
Power supply module failure
The whole rack goes dark or resets. Ageing capacitors and supply surges are the usual causes.
I/O channel damage
Single dead inputs or outputs after a short or surge on field wiring. The module is repaired and every channel tested.
CPU faults and lost programs
A CPU stuck in stop or fault mode, or a lost program from a flat memory battery. Keep a current backup of the program.
Communication module faults
Loss of the network to drives, remote I/O or the SCADA system, with the CPU itself healthy.
Backplane and connector problems
Intermittent module faults caused by the rack, connectors or vibration rather than the module.
Communication
Communication faults can be in the module, the cable or the network configuration. The module is tested on a live link after repair; the cabling and terminations at site are worth checking too.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note the CPU and module LEDs and any diagnostic buffer messages.
- Check the supply voltage to the rack.
- Take a program backup while the CPU still runs.
- Check field wiring for shorts before fitting a replacement module.
Leave to a specialist
- Downloading or modifying the program.
- Working on live I/O wiring.
- Replacing CPU firmware or memory.
Getting it fixed
How to get the PLC IC695ETM001-EJ RX3i repaired
What to send with it
- The failed module, labelled with its slot position.
- The LED states and any diagnostic message.
- A program backup if a CPU is being sent.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
PLC IC695ETM001-EJ RX3i repair questions
Will the GE Fanuc PLC IC695ETM001-EJ RX3i keep its program after repair?+
A repair doesn't normally touch the user program, but a CPU should always be sent with a current backup in case its memory has been affected by the fault.
Can obsolete PLC modules still be repaired?+
Yes. Discontinued modules are usually worth repairing, because replacements are scarce and changing platforms means rewriting the program.
Does the GE Fanuc PLC IC695ETM001-EJ RX3i have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to GE Fanuc?+
No. GE Fanuc and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by GE Fanuc.
Same manufacturer
Other GE Fanuc PLCs & I/O Modules
Other manufacturers
PLCs & I/O Modules from other makers
GE Fanuc and PLC IC695ETM001-EJ RX3i are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by GE Fanuc.
PLC IC695ETM001-EJ RX3i down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.