Gic Systems · Excitation & Generator Controls
Gic Systems SM500 MG73B9 repair
Send the Gic Systems SM500 MG73B9 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original excitation or generator control, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Gic Systems SM500 MG73B9
- Manufacturer
- Gic Systems
- Model / part number
- SM500 MG73B9
- Also searched as
- SM500MG73B9
- Description
- Voltage monitoring relay
- Category
- Excitation & Generator Controls
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Gic Systems equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the SM500 MG73B9
Excitation systems and generator controls regulate voltage and protect the generator, so faults show up as unstable voltage, field failures or tripping on load. AVR boards, thyristor bridges, controllers and engine control units can be repaired and tested.
Voltage hunting or instability
AVR control faults, sensing problems or worn feedback components.
Field failure and loss of excitation
Failed field thyristors or diodes, firing circuits or a fault in the exciter.
Overvoltage or undervoltage trips
Sensing circuit faults or wrong settings after a board change.
Controller and display faults
Dead controllers, lost settings and failed communication with switchgear.
Engine control unit faults
Speed control, sensor input and actuator driver faults on gensets.
Relays and contacts
Relay outputs are checked for contact resistance and correct operation, since worn contacts give intermittent faults.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Record alarms and event logs from the controller.
- Note the load and conditions when the fault appeared.
- Keep a copy of the controller settings.
Leave to a specialist
- Work on the field circuit or exciter.
- AVR tuning and setting after repair.
- Any test on a running generator.
Getting it fixed
How to get the SM500 MG73B9 repaired
What to send with it
- The AVR, exciter board or controller.
- The generator rating and the alarm or log.
- Its settings, if they can be read out.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
SM500 MG73B9 repair questions
Does the Gic Systems SM500 MG73B9 need setting up after repair?+
Usually its settings are kept, but voltage regulation and any limits should be checked on the generator when it is refitted.
Does the Gic Systems SM500 MG73B9 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Gic Systems?+
No. Gic Systems and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Gic Systems.
Other manufacturers
Excitation & Generator Controls from other makers
Gic Systems and SM500 MG73B9 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Gic Systems.
SM500 MG73B9 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.