Heidelberg · Motion & Speed Controllers
Heidelberg 00.785.0278/06 repair
Component-level repair for the Heidelberg 00.785.0278/06 (power supply, drive dc bus), onsite or sent in from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Heidelberg 00.785.0278/06
- Manufacturer
- Heidelberg
- Model / part number
- 00.785.0278/06
- Also searched as
- 00785027806 · 00 785 0278 06 · 785027806
- Description
- Power supply, drive DC bus
- Category
- Motion & Speed Controllers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Heidelberg printing presses, including Speedmaster, Printmaster and GTO machines, carry many machine-specific control, drive and interface boards. Spares for older presses are often hard to source, which makes board repair the practical option.
Common faults
What usually fails on a unit like the 00.785.0278/06
Motion controllers, regulators and machine-specific drive cards coordinate speed, position or current. Faults appear as wrong movement, trips or loss of control, and the card is usually repairable at component level.
Loss of control or wrong speed
Faults in feedback inputs, reference signals or the control loop on the card.
Card dead or resetting
On-board supply faults and failed processors or memory.
Communication faults
Lost connection with the PLC, drives or the operator panel.
Output stage faults
Failed drivers for valves, contactors or power stages.
Crane and hoist control faults
Radio remote, interlock and speed-control faults on cranes and hoists.
Power section
This is a power part, so it is checked under real load after repair, not just for output voltage at no load. Ageing capacitors and switching devices are replaced as found, since they are the usual cause.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note LEDs, alarm codes and when the fault occurs.
- Check reference and feedback wiring.
- Check the card's supply voltage.
Leave to a specialist
- Component-level repair and testing.
- Setting and tuning control loops.
- Work on crane and hoist safety circuits.
Getting it fixed
How to get the 00.785.0278/06 repaired
What to send with it
- The card or controller, with any plug-in modules.
- The machine it comes from and the fault seen.
- Its settings or jumper positions, photographed before removal.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
00.785.0278/06 repair questions
Can the Heidelberg 00.785.0278/06 be repaired without drawings?+
In most cases. Boards are traced and repaired at component level and tested with their inputs and outputs simulated.
Does the Heidelberg 00.785.0278/06 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Heidelberg?+
No. Heidelberg and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Heidelberg.
Same manufacturer
Other Heidelberg Motion & Speed Controllers
Other manufacturers
Motion & Speed Controllers from other makers
Heidelberg and 00.785.0278/06 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Heidelberg.
00.785.0278/06 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.