Rexroth · HMIs, Operator Panels & Displays
Rexroth HMI VCP05.2DSN-003-SR-NN-PW repair
Component-level repair for the Rexroth HMI VCP05.2DSN-003-SR-NN-PW (indracontrol vcp 05), onsite or sent in from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Rexroth HMI VCP05.2DSN-003-SR-NN-PW
- Manufacturer
- Rexroth
- Model / part number
- HMI VCP05.2DSN-003-SR-NN-PW
- Also searched as
- HMIVCP052DSN003SRNNPW · HMI VCP05 2DSN 003 SR NN PW
- Description
- IndraControl VCP 05
- Category
- HMIs, Operator Panels & Displays
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Bosch Rexroth supplies drives and controls (IndraDrive, DIAX and EcoDrive servo systems, IndraMotion and IndraControl) and hydraulics, including proportional and servo valves and their amplifier electronics.
Common faults
What usually fails on a unit like the HMI VCP05.2DSN-003-SR-NN-PW
Operator panels and industrial displays fail in the touch screen, the backlight, the power section or the memory that holds the application. Most of these can be repaired with the screens and recipes kept.
Touch screen not responding or drifting
Worn or cracked touch glass, or a failed touch controller. The touch layer can usually be replaced on its own.
Dim or blank display
Failed backlight or backlight inverter. The panel still runs, which can be confirmed by touch response or communication.
Panel won't boot
A failed power section, corrupted memory card or flash, or a damaged mainboard.
Communication loss with the PLC
A damaged serial or Ethernet port, or a configuration problem after a power event.
Lines or patches on the screen
LCD panel or ribbon connector faults, often after impact or heat.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note whether the panel powers up, shows anything, or responds to touch.
- Check the supply voltage at the panel.
- Back up the application project if the panel still runs.
Leave to a specialist
- Replacing touch glass, LCD or backlight.
- Restoring or transferring the application.
- Board-level repair of the mainboard or power section.
Getting it fixed
How to get the HMI VCP05.2DSN-003-SR-NN-PW repaired
What to send with it
- The panel, with its memory card if it has one.
- The application project file, if you have it.
- A description of the fault and a photo of the screen.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
HMI VCP05.2DSN-003-SR-NN-PW repair questions
Will the screens and recipes on the Rexroth HMI VCP05.2DSN-003-SR-NN-PW be kept?+
Repairs to the touch screen, backlight or power section don't affect the application. If the mainboard or memory has failed, sending the project file lets it be restored.
Can only the touch glass be replaced?+
On most panels, yes. The touch layer is replaced and calibrated, and the rest of the panel is tested before return.
Does the Rexroth HMI VCP05.2DSN-003-SR-NN-PW have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Rexroth?+
No. Rexroth and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Rexroth.
Same manufacturer
Other Rexroth HMIs, Operator Panels & Displays
Other manufacturers
HMIs, Operator Panels & Displays from other makers
Rexroth and HMI VCP05.2DSN-003-SR-NN-PW are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Rexroth.
HMI VCP05.2DSN-003-SR-NN-PW down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.