Schneider Electric · Power Supplies & UPS
Schneider Electric 140 CPS 124 repair
Send the Schneider Electric 140 CPS 124 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original power supply, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Schneider Electric 140 CPS 124
- Manufacturer
- Schneider Electric
- Model / part number
- 140 CPS 124
- Also searched as
- 140CPS124
- Description
- Power supply card, 20 LMS AC PS 115/230V RED PLC
- Category
- Power Supplies & UPS
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Schneider Electric covers Altivar drives, Lexium servo systems, Modicon PLCs, Magelis and Harmony operator panels, soft starters, relays and power supplies, as well as older Telemecanique-branded products still in service.
Common faults
What usually fails on a unit like the 140 CPS 124
Power supplies are the most common single cause of machine electronics failing. Switched-mode supplies wear out in predictable places, mainly capacitors, switching transistors and fans, and almost all of them can be repaired and load-tested.
No output
Failed fuse, switching transistor, controller IC or startup circuit, often triggered by a surge.
Low, noisy or drifting output
Dried-out electrolytic capacitors are the most common cause, and they cause resets and odd faults in the equipment downstream.
Shutdown under load
Overload protection tripping because of a weak supply, or a short in the load.
Overheating
Failed fans and dust build-up in fan-cooled supplies and UPS units.
UPS battery and charger faults
Ageing batteries and failed charger circuits reduce backup time or cause transfer failures.
Power section
This is a power part, so it is checked under real load after repair, not just for output voltage at no load. Ageing capacitors and switching devices are replaced as found, since they are the usual cause.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Measure the output voltage with and without load.
- Disconnect the load to see whether the supply or the load is at fault.
- Check fans and ventilation.
Leave to a specialist
- Opening a supply: its capacitors hold a charge after switch-off.
- Component-level repair and load testing.
- Battery replacement in UPS units.
Getting it fixed
How to get the 140 CPS 124 repaired
What to send with it
- The supply or UPS module.
- Its input and output ratings if the label is unreadable.
- What it feeds, and whether it failed suddenly or gradually.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
140 CPS 124 repair questions
Is it worth repairing the Schneider Electric 140 CPS 124 rather than buying a new one?+
For standard supplies it depends on availability and price; for machine-specific, discontinued or high-power supplies, repair is usually the practical route because an exact replacement may not exist.
Does the Schneider Electric 140 CPS 124 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Schneider Electric?+
No. Schneider Electric and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Schneider Electric.
Same manufacturer
Other Schneider Electric Power Supplies & UPS
Other manufacturers
Power Supplies & UPS from other makers
Schneider Electric and 140 CPS 124 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Schneider Electric.
140 CPS 124 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.