Siemens · Motion & Speed Controllers
Siemens INT-2X50A repair
Send the Siemens INT-2X50A for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original motion controller, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Siemens INT-2X50A
- Manufacturer
- Siemens
- Model / part number
- INT-2X50A
- Also searched as
- INT2X50A · INT 2X50A
- Description
- SIMODRIVE lt-module 1p 6SN1118-0NH01-0AA1
- Category
- Motion & Speed Controllers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Siemens automation and drives equipment, including SIMATIC PLCs and HMIs, SINAMICS and MICROMASTER drives, SIMOREG DC drives and SINUMERIK CNC controls, is found across Indian manufacturing and process plants, often running alongside older generations of the same family.
Common faults
What usually fails on a unit like the INT-2X50A
Motion controllers, regulators and machine-specific drive cards coordinate speed, position or current. Faults appear as wrong movement, trips or loss of control, and the card is usually repairable at component level.
Loss of control or wrong speed
Faults in feedback inputs, reference signals or the control loop on the card.
Card dead or resetting
On-board supply faults and failed processors or memory.
Communication faults
Lost connection with the PLC, drives or the operator panel.
Output stage faults
Failed drivers for valves, contactors or power stages.
Crane and hoist control faults
Radio remote, interlock and speed-control faults on cranes and hoists.
Board-level repair
This is repaired at component level: the board is traced, the failed parts are replaced, and the board is tested with its inputs and outputs before it is returned.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note LEDs, alarm codes and when the fault occurs.
- Check reference and feedback wiring.
- Check the card's supply voltage.
Leave to a specialist
- Component-level repair and testing.
- Setting and tuning control loops.
- Work on crane and hoist safety circuits.
Getting it fixed
How to get the INT-2X50A repaired
What to send with it
- The card or controller, with any plug-in modules.
- The machine it comes from and the fault seen.
- Its settings or jumper positions, photographed before removal.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
INT-2X50A repair questions
Can the Siemens INT-2X50A be repaired without drawings?+
In most cases. Boards are traced and repaired at component level and tested with their inputs and outputs simulated.
Does the Siemens INT-2X50A have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Siemens?+
No. Siemens and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Siemens.
Same manufacturer
Other Siemens Motion & Speed Controllers
Other manufacturers
Motion & Speed Controllers from other makers
Siemens and INT-2X50A are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Siemens.
INT-2X50A down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.