Sigmatek · PLCs & I/O Modules
Sigmatek DCC 080 repair
Get the Sigmatek DCC 080 repaired rather than replaced. It is matched to an engineer who works on Sigmatek PLC modules, and the cost is confirmed before work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Sigmatek DCC 080
- Manufacturer
- Sigmatek
- Model / part number
- DCC 080
- Also searched as
- DCC080
- Description
- Processor module
- Category
- PLCs & I/O Modules
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Sigmatek equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the DCC 080
PLC hardware is reliable, so when a module fails there is usually a clear cause: power supply stress, a surge on field wiring, heat, or age. CPUs, I/O modules, communication cards and power supplies can be repaired and tested on a live rack.
Power supply module failure
The whole rack goes dark or resets. Ageing capacitors and supply surges are the usual causes.
I/O channel damage
Single dead inputs or outputs after a short or surge on field wiring. The module is repaired and every channel tested.
CPU faults and lost programs
A CPU stuck in stop or fault mode, or a lost program from a flat memory battery. Keep a current backup of the program.
Communication module faults
Loss of the network to drives, remote I/O or the SCADA system, with the CPU itself healthy.
Backplane and connector problems
Intermittent module faults caused by the rack, connectors or vibration rather than the module.
Processor board
Processor boards hold firmware and often configuration. The repair works around the memory where possible; send any backup you have, and note the firmware version if the system shows it.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Note the CPU and module LEDs and any diagnostic buffer messages.
- Check the supply voltage to the rack.
- Take a program backup while the CPU still runs.
- Check field wiring for shorts before fitting a replacement module.
Leave to a specialist
- Downloading or modifying the program.
- Working on live I/O wiring.
- Replacing CPU firmware or memory.
Getting it fixed
How to get the DCC 080 repaired
What to send with it
- The failed module, labelled with its slot position.
- The LED states and any diagnostic message.
- A program backup if a CPU is being sent.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
DCC 080 repair questions
Will the Sigmatek DCC 080 keep its program after repair?+
A repair doesn't normally touch the user program, but a CPU should always be sent with a current backup in case its memory has been affected by the fault.
Can obsolete PLC modules still be repaired?+
Yes. Discontinued modules are usually worth repairing, because replacements are scarce and changing platforms means rewriting the program.
Does the Sigmatek DCC 080 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Sigmatek?+
No. Sigmatek and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Sigmatek.
Same manufacturer
Other Sigmatek PLCs & I/O Modules
Other manufacturers
PLCs & I/O Modules from other makers
Sigmatek and DCC 080 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Sigmatek.
DCC 080 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.