Atlas Copco · DCS & Control Systems
Atlas Copco 1900 0710 repair
Component-level repair for the Atlas Copco 1900 0710 (elektronikon controller 02), onsite or sent in from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Atlas Copco 1900 0710
- Manufacturer
- Atlas Copco
- Model / part number
- 1900 0710
- Also searched as
- 19000710
- Description
- Elektronikon controller 02
- Category
- DCS & Control Systems
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Atlas Copco compressors use Elektronikon controllers, drives and sensor electronics, which are repairable when they fail.
Common faults
What usually fails on a unit like the 1900 0710
DCS hardware is built for long service, so plants often keep a system running well past the maker's support period. Controllers, I/O cards, power supplies and communication modules can be repaired and tested so the system stays as it is.
I/O card channel failures
Analog and digital channels damaged by field surges, earth faults or water ingress in junction boxes.
Power supply degradation
Ageing supplies cause noisy readings, card resets or redundancy alarms long before they fail outright.
Controller and processor faults
Controller failovers, memory errors or a redundant controller that won't synchronise.
Communication and network modules
Bus or network faults between controllers, I/O and operator stations.
Connector and backplane wear
Intermittent faults from oxidised connectors and backplanes, common in humid or dusty control rooms.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Record the system diagnostic messages and which card or channel is affected.
- Check whether the fault moves when redundant modules are switched over.
- Check cabinet temperature and fans.
Leave to a specialist
- Removing or inserting cards on a running system.
- Controller configuration, firmware and redundancy work.
- Any change that affects a running process.
Getting it fixed
How to get the 1900 0710 repaired
What to send with it
- The failed card or module with its slot and node noted.
- The system's diagnostic message or a screenshot.
- Whether the card is part of a redundant pair.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
1900 0710 repair questions
Can the Atlas Copco 1900 0710 be repaired after the maker has ended support?+
In most cases. Repairing the existing cards keeps the system and its configuration unchanged, which is far less disruptive than a migration.
Does the Atlas Copco 1900 0710 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Atlas Copco?+
No. Atlas Copco and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Atlas Copco.
Same manufacturer
Other Atlas Copco DCS & Control Systems
Other manufacturers
DCS & Control Systems from other makers
Atlas Copco and 1900 0710 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Atlas Copco.
1900 0710 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.