B&R · Encoders & Resolvers
B&R PC 5PC910 SX02-00 repair
Send the B&R PC 5PC910 SX02-00 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original encoder, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The B&R PC 5PC910 SX02-00
- Manufacturer
- B&R
- Model / part number
- PC 5PC910 SX02-00
- Also searched as
- PC5PC910SX0200 · PC 5PC910 SX02 00
- Description
- Automation
- Category
- Encoders & Resolvers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
B&R (now part of ABB) makes machine automation hardware: X20 and older PLC systems, Power Panel and Automation PC operator units, and ACOPOS servo drives with matching motors. It is common on packaging, printing and plastics machinery.
Common faults
What usually fails on a unit like the PC 5PC910 SX02-00
Encoders and resolvers tell the drive where the motor and axis are. A fault shows up as feedback alarms, position errors or a motor that won't run. Many encoders can be repaired; all need checking for correct signals and alignment.
Signal loss or noise
Damaged cables, contaminated discs or failing electronics cause intermittent feedback alarms.
Bearing and shaft wear
Worn encoder bearings cause signal jitter and eventually mechanical failure.
Contamination
Oil, coolant or dust on the code disc gives counting errors and lost position.
Absolute encoder data errors
Battery or memory faults on absolute encoders lose the stored position.
Connector damage
Bent pins and corroded connectors, common where cables are flexed or exposed.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the encoder cable and connectors along their full length.
- Note the exact feedback alarm from the drive.
- Check for oil or coolant ingress at the encoder housing.
Leave to a specialist
- Opening the encoder or cleaning the code disc.
- Aligning an encoder to a motor rotor.
- Re-referencing an absolute encoder.
Getting it fixed
How to get the PC 5PC910 SX02-00 repaired
What to send with it
- The encoder, and the motor if the encoder is built into it.
- The drive alarm and the drive model it connects to.
- Whether the fault is constant or intermittent.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
PC 5PC910 SX02-00 repair questions
Does the B&R PC 5PC910 SX02-00 need to be aligned after repair?+
If it mounts on a servo motor, yes: it has to be aligned to the rotor so the drive commutates correctly. That is part of the repair when the motor is sent too.
Does the B&R PC 5PC910 SX02-00 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to B&R?+
No. B&R and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by B&R.
Same manufacturer
Other B&R Encoders & Resolvers
Other manufacturers
Encoders & Resolvers from other makers
B&R and PC 5PC910 SX02-00 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by B&R.
PC 5PC910 SX02-00 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.