Heidelberg · Stepper Motors & Drives
Heidelberg L6-170-0903 repair
Send the Heidelberg L6-170-0903 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original stepper unit, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Heidelberg L6-170-0903
- Manufacturer
- Heidelberg
- Model / part number
- L6-170-0903
- Also searched as
- L61700903 · L6 170 0903
- Description
- Panel, stepper motor control
- Category
- Stepper Motors & Drives
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Heidelberg printing presses, including Speedmaster, Printmaster and GTO machines, carry many machine-specific control, drive and interface boards. Spares for older presses are often hard to source, which makes board repair the practical option.
Common faults
What usually fails on a unit like the L6-170-0903
Stepper motors and drives are simple but run in demanding, fast-indexing duty. Drive faults usually sit in the output stage or supply; motor faults in bearings, windings and connectors.
Lost steps and stalling
Weak drive current, a failing supply, mechanical binding or a worn motor.
Drive output stage failure
Shorted output transistors after a winding or cable fault.
Overheating
Motor current set too high, or drives without enough cooling.
Bearing wear and noise
Worn motor bearings cause noise, resonance and position errors.
Connector faults
Loose or corroded connectors give erratic movement.
Display and touch
Display faults are usually in the backlight, the LCD, the touch layer or the display driver. These are repaired separately, so a cracked touch screen does not mean replacing the whole unit.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the mechanism turns freely by hand with power off.
- Check connectors and cables.
- Note the drive's alarm LED state.
Leave to a specialist
- Drive board repair.
- Setting current and microstepping to suit the load.
Getting it fixed
How to get the L6-170-0903 repaired
What to send with it
- The drive and, if possible, the motor.
- The supply voltage and the current setting.
- What the axis does and where it loses position.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
L6-170-0903 repair questions
Should the motor be sent with the Heidelberg L6-170-0903?+
If the fault is lost steps or stalling, yes: testing them together shows whether the drive, the motor or the mechanics are at fault.
Does the Heidelberg L6-170-0903 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Heidelberg?+
No. Heidelberg and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Heidelberg.
Same manufacturer
Other Heidelberg Stepper Motors & Drives
Other manufacturers
Stepper Motors & Drives from other makers
Heidelberg and L6-170-0903 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Heidelberg.
L6-170-0903 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.