K-tron Feeder Group · Temperature & Process Controllers
K-tron Feeder Group 005987 repair
Get the K-tron Feeder Group 005987 repaired rather than replaced. It is matched to an engineer who works on K-tron Feeder Group controllers, and the cost is confirmed before work starts.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The K-tron Feeder Group 005987
- Manufacturer
- K-tron Feeder Group
- Model / part number
- 005987
- Also searched as
- 5987
- Description
- Drive power card
- Category
- Temperature & Process Controllers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
K-tron Feeder Group equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the 005987
Temperature, PID and burner controllers are small but critical: when one fails, a furnace, oven or process loop stops. Most faults are in the power section, input circuits or output relays, and the controller can be repaired and checked against a calibrated source.
Wrong or unstable reading
Damaged thermocouple or RTD input circuits, often from a sensor short or a surge on the sensor wiring.
Output not switching
Burnt output relays, failed SSR drivers or damaged analog output stages.
Dead display
Failed internal power supply or display driver.
Lost configuration
Memory faults that reset the input type, range or alarms.
Burner sequence faults
Flame detection, valve proving and ignition faults in burner controllers.
Power section
This is a power part, so it is checked under real load after repair, not just for output voltage at no load. Ageing capacitors and switching devices are replaced as found, since they are the usual cause.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the sensor and its wiring before blaming the controller.
- Note the input type and range configured.
- Record the alarm or error shown.
Leave to a specialist
- Calibrating inputs and outputs.
- Any work on burner management and flame safety systems.
- Changing control configuration on a running process.
Getting it fixed
How to get the 005987 repaired
What to send with it
- The controller.
- Its input type, range and output configuration if known.
- The sensor type it reads.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
005987 repair questions
Is the K-tron Feeder Group 005987 calibrated after repair?+
The input is checked against a calibrated source over its range, and outputs are confirmed to switch, so the controller reads and acts correctly when refitted.
Does the K-tron Feeder Group 005987 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to K-tron Feeder Group?+
No. K-tron Feeder Group and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by K-tron Feeder Group.
Other manufacturers
Temperature & Process Controllers from other makers
K-tron Feeder Group and 005987 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by K-tron Feeder Group.
005987 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.