Larsen & Toubro · Protection Relays
Larsen & Toubro MCOM ZX80032 repair
Send the Larsen & Toubro MCOM ZX80032 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original protection relay, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Larsen & Toubro MCOM ZX80032
- Manufacturer
- Larsen & Toubro
- Model / part number
- MCOM ZX80032
- Also searched as
- MCOMZX80032
- Description
- Relay
- Category
- Protection Relays
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Larsen & Toubro equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the MCOM ZX80032
Protection relays have to trip when needed and stay quiet otherwise, so a repaired relay must be tested against its settings, not just powered up. Power supplies, input boards, displays and output contacts are the usual failure points.
Relay dead or rebooting
Failed internal power supply, often from age or a surge on the auxiliary supply.
Self-supervision or internal fault alarms
Faults in the processor board, memory or analog input stages.
Wrong measurement
Current or voltage inputs reading wrongly because of damaged input transformers or analog circuits.
Output contacts not operating
Burnt or welded output relay contacts, or failed driver circuits.
Display and keypad faults
Unreadable displays and dead keys, which make settings hard to check.
Relays and contacts
Relay outputs are checked for contact resistance and correct operation, since worn contacts give intermittent faults.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Record any self-supervision alarm and the event log.
- Check the auxiliary supply voltage.
- Keep a copy of the settings file.
Leave to a specialist
- Secondary injection testing after repair.
- Changing or uploading relay settings.
- Any work on CT and VT circuits: open CT secondaries are dangerous.
Getting it fixed
How to get the MCOM ZX80032 repaired
What to send with it
- The relay, with its settings file if possible.
- The alarm or event log.
- The CT and VT ratings it is set for.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
MCOM ZX80032 repair questions
How is the Larsen & Toubro MCOM ZX80032 tested after repair?+
Beyond powering up, the relay is checked with secondary injection so its measuring inputs, protection functions and output contacts are confirmed to work.
Does the Larsen & Toubro MCOM ZX80032 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Larsen & Toubro?+
No. Larsen & Toubro and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Larsen & Toubro.
Other manufacturers
Protection Relays from other makers
Larsen & Toubro and MCOM ZX80032 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Larsen & Toubro.
MCOM ZX80032 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.