Sma · Temperature & Process Controllers
Sma SCCOMGR6-00-01 repair
Send the Sma SCCOMGR6-00-01 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original controller, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Sma SCCOMGR6-00-01
- Manufacturer
- Sma
- Model / part number
- SCCOMGR6-00-01
- Also searched as
- SCCOMGR60001 · SCCOMGR6 00 01
- Description
- Communication controller
- Category
- Temperature & Process Controllers
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Sma equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the SCCOMGR6-00-01
Temperature, PID and burner controllers are small but critical: when one fails, a furnace, oven or process loop stops. Most faults are in the power section, input circuits or output relays, and the controller can be repaired and checked against a calibrated source.
Wrong or unstable reading
Damaged thermocouple or RTD input circuits, often from a sensor short or a surge on the sensor wiring.
Output not switching
Burnt output relays, failed SSR drivers or damaged analog output stages.
Dead display
Failed internal power supply or display driver.
Lost configuration
Memory faults that reset the input type, range or alarms.
Burner sequence faults
Flame detection, valve proving and ignition faults in burner controllers.
Communication
Communication faults can be in the module, the cable or the network configuration. The module is tested on a live link after repair; the cabling and terminations at site are worth checking too.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the sensor and its wiring before blaming the controller.
- Note the input type and range configured.
- Record the alarm or error shown.
Leave to a specialist
- Calibrating inputs and outputs.
- Any work on burner management and flame safety systems.
- Changing control configuration on a running process.
Getting it fixed
How to get the SCCOMGR6-00-01 repaired
What to send with it
- The controller.
- Its input type, range and output configuration if known.
- The sensor type it reads.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
SCCOMGR6-00-01 repair questions
Is the Sma SCCOMGR6-00-01 calibrated after repair?+
The input is checked against a calibrated source over its range, and outputs are confirmed to switch, so the controller reads and acts correctly when refitted.
Does the Sma SCCOMGR6-00-01 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Sma?+
No. Sma and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Sma.
Other manufacturers
Temperature & Process Controllers from other makers
Sma and SCCOMGR6-00-01 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Sma.
SCCOMGR6-00-01 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.