Jenaer Antriebstechnik GMBH · Stepper Motors & Drives
Jenaer Antriebstechnik GMBH ECOSTEP 100-AA-800-000 repair
Send the Jenaer Antriebstechnik GMBH ECOSTEP 100-AA-800-000 for diagnosis and repair, or have an engineer come to the plant. Repair keeps the original stepper unit, its settings and its wiring in place.
Cost confirmed before any work starts · Warranty of 30 days to 6 months
At a glance
The Jenaer Antriebstechnik GMBH ECOSTEP 100-AA-800-000
- Manufacturer
- Jenaer Antriebstechnik GMBH
- Model / part number
- ECOSTEP 100-AA-800-000
- Also searched as
- ECOSTEP100AA800000 · ECOSTEP 100 AA 800 000
- Description
- Stepper motor drive
- Category
- Stepper Motors & Drives
- Service
- Diagnosis and component-level repair, onsite or ship-in
- Warranty
- 30 days to 6 months, confirmed before work starts
Jenaer Antriebstechnik GMBH equipment in this catalog is listed by model or part number. Send the model from the nameplate and the fault, and it will be matched to an engineer who works on that kind of unit.
Common faults
What usually fails on a unit like the ECOSTEP 100-AA-800-000
Stepper motors and drives are simple but run in demanding, fast-indexing duty. Drive faults usually sit in the output stage or supply; motor faults in bearings, windings and connectors.
Lost steps and stalling
Weak drive current, a failing supply, mechanical binding or a worn motor.
Drive output stage failure
Shorted output transistors after a winding or cable fault.
Overheating
Motor current set too high, or drives without enough cooling.
Bearing wear and noise
Worn motor bearings cause noise, resonance and position errors.
Connector faults
Loose or corroded connectors give erratic movement.
Motor
Motors are checked for winding insulation, bearings and feedback, and run after repair. If it carries an encoder, the encoder is checked for correct signals and alignment.
First checks
What to check before calling an engineer
Isolate and lock out the supply, and wait for stored energy to discharge, before opening anything.
Safe for plant staff
- Check the mechanism turns freely by hand with power off.
- Check connectors and cables.
- Note the drive's alarm LED state.
Leave to a specialist
- Drive board repair.
- Setting current and microstepping to suit the load.
Getting it fixed
How to get the ECOSTEP 100-AA-800-000 repaired
What to send with it
- The drive and, if possible, the motor.
- The supply voltage and the current setting.
- What the axis does and where it loses position.
Onsite or ship-in
Technicians work onsite from our Hyderabad base and travel to plants across India; anything that can be removed can also be sent to MachineryFix from anywhere in the country.
Warranty. Repairs carry a warranty of 30 days to 6 months, depending on the item and the repair; the exact term is confirmed before work starts.
FAQ
ECOSTEP 100-AA-800-000 repair questions
Should the motor be sent with the Jenaer Antriebstechnik GMBH ECOSTEP 100-AA-800-000?+
If the fault is lost steps or stalling, yes: testing them together shows whether the drive, the motor or the mechanics are at fault.
Does the Jenaer Antriebstechnik GMBH ECOSTEP 100-AA-800-000 have to be sent in, or can an engineer come to the plant?+
Either. An engineer can diagnose it in place and repair it there or take it away, or the unit can be sent to MachineryFix from anywhere in India. The diagnosis and repair cost are confirmed before any work starts.
Is MachineryFix connected to Jenaer Antriebstechnik GMBH?+
No. Jenaer Antriebstechnik GMBH and the model name are used only to identify the equipment. MachineryFix is an independent repair service and is not affiliated with or endorsed by Jenaer Antriebstechnik GMBH.
Other manufacturers
Stepper Motors & Drives from other makers
Jenaer Antriebstechnik GMBH and ECOSTEP 100-AA-800-000 are named only to identify the equipment. MachineryFix is not affiliated with or endorsed by Jenaer Antriebstechnik GMBH.
ECOSTEP 100-AA-800-000 down?
Send the fault and what the machine was doing. We'll match an engineer who works on it.